Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5846 gości 
Kategorie
Informacje
Polecamy
Strona główna >> PIONEER >> MEHP5150 Instrukcja Serwisowa
 
 0 szt. w koszyku 

PIONEER MEHP5150
Instrukcja Serwisowa


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Zawiera schematy
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis PIONEER MEHP5150 Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schematy, diagramy drukowanych obwodów (PCB), schematy połączeń, schematy blokowe oraz katalog części. Instrukcje serwisowe są wykorzystywane glównie przez osoby naprawiające uszkodzony sprzęt.

Jeśli chcesz się dowiedzieć jak się obsługuje Twój telewizor, magnetowid, odtwarzacz mp3 itp. powinieneś raczej szukać instrukcji obsługi

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!
Recenzje innych produktów
 TX7520 ONKYO Instrukcja Serwisowa by Robert Teodorski;
Schematy są ale można wysilić się i zrobić kolorowy skan i o większej rozdzielczości. Wtedy schematy płytek będą czytelniejsze. Całość super jako wartość merytoryczna. Wszystkie dane potrzebne do podłączenia różnego rodzajów urządzeń takich gramofon, CD itd.
 CTV323 CLATRONIC Instrukcja Serwisowa by Bogdan Padechowicz;
Szybko, sprawnie i tanio. Serwis godny polecenia. Będę polecał innym
 CC8065 DUAL Instrukcja Serwisowa by Zbigniew Szarycz;
Ogólnie jest OK, z wyjątkiem obrazu płyty głównej, który jest miejscami mało czytelny, ale można sobie poradzić.
 KPE61MN11 SONY Instrukcja Serwisowa by Grzegorz Zawadzki;
Dokładna dokumentacja, pomogła w szybkiej naprawie telewizora. Dziękuję!
 RCM70L/LB JVC Instrukcja Serwisowa by Damian Mazek;
jedyne do czego mogę mieć zastrzeżenie to jakość zdjęć zawartych w przesłanej instrukcji serwisowej ponieważ są fatalnej jakości, praktycznie nieczytelne. tak poza tym jestem zadowolony to jest to czego szukałem.

Tekstowy podgląd strony 65 (kliknij aby zobaczyć)
MEH-P5100R,P5150

6. ADJUSTMENT
6.1 ADJUSTING THE MD SECTION
1) Precautions Since the single voltage (3.3V) system is being employed for the regulator of this equipment, the reference potential for the servo signals becomes Vc (1.65V, approximately). In this manual, the Vc reference potential will be indicated as **Vc (e.g. 1.5Vc) and the reference GND will be indicated as **V. If connection errors of the Vc and the GND are made while product adjustment is being made, it becomes unfeasible to measure the electric potential correctly and, moreover, the servo can make malfunctioning to apply severe impacts to the pick up. Consequently, to prevent occurrence of such an error, observe the followings. 1. Do not make connection errors of the Vc and the GND when connecting the negative side of the probe of the instrument. For example, do not connect the Vc to the negative side of the probe ch1 nor connect the GND to the negative side of the probe ch2 of the oscilloscope. Also, since the measuring instrument proper usually carries the same potential as that of the negative side of the probe, in many cases, set the measuring instrument proper to a floated state. 2. When installing and removing the filters and wires necessary for the measurement work, always turn �OFF� the regulator. 3. Since various protection means of the software are not valid under the test mode, be careful not to apply mechanical shock and electric shocks while adjustment work is in progress. 4. This equipment works to discriminate the discs namely, high reflection discs (premaster) and low reflection discs (recordable), when the discrimination SW is duly operated. (High reflection Disc=0V and low reflection Disc=5V with the CN401 / 4-pin / Contact Pin Name: DISC as is shown in the circuit diagram) Disc discrimination can be confirmed by the following indications appearing under the TEST MD mode, after completing floating of the disc under the TEST mode. In case of high refection: 02200000 In case of low refection: 01100000 (The second and third digits counting from the Left-hand side will become �2� or �1�.) Unless disc discrimination is made properly, accurate automatic adjustment and grating adjustment cannot be expected and always confirm the above when starting up the TEST mode. 2)LD protection for the pickup Unlike MD pickups, the MD pickups being used for this equipment are not equipped with the LD protection short pin but, instead, a shorting land by soldering is being provided. When removing, make a shorting by soldering before removing the flex. To protect the flex., limit the time to apply the soldering iron to a short time. Reference application time: within 2 seconds. 3)Regarding the TEST mode This mode should be used when adjusting and inspecting the MD mechanism module of this equipment. 1. When entering into the TEST mode: Pressing and holding the �4� key and �6� key simultaneously, turn ON the �B.u� and �Acc� at the same time. Select the �MD Source� using the SOURCE key. (Keep the Disc inserted.) 2. When canceling the TEST mode: Turn OFF the �B.u� and �Acc�. 3. When turning ON the power supply Press the key �BAND� to start up the 3.3v for the MD regulator. Meanwhile, pay attention to the fact that the microcomputer supply power Vdd5v starts up when the �B.u� and �Acc� are turned on. 4. Measuring LD electric current When measuring the voltage between 3VD and VI using a multimeter or the like, be sure to connect the measuring instrument on the power supply off before turning on the power supply. If you make contact between 3VD and VI using a clip or the like after turning on the power supply, the noise could cause LD failure.

65

Klienci kupując ten produkt kupili także

$4.99

MEHP5150 PIONEER
Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email…
>
Parse Time: 0.172 - Number of Queries: 110 - Query Time: 0.039